« previous next »
Pages: [1]   Go Down

Author Topic: Turncrafter Pro VS DIED!!!!!!  (Read 359 times)

Offline Fyrewil

  • Custom Call Maker
  • *****
  • Posts: 13
Turncrafter Pro VS DIED!!!!!!
« on: March 09, 2010, 10:21:52 PM »
Less than  2 month's old my New Turncrafter Pro VS died. Was turning a 1.5 block and the motor just stopped working....( was actually changing tools, talking to my daughter when it happened)
Checked circuit breakers, control reset, changed outlets, no smell from motor.... Just stopped working.
I see Penn state no longer carries the "Turncrafter Pro" (Hummm)  :huh:
Did a little surfing and found some negative feedback for the turncrafter pro vs for the exact same Reason... Just stops running for no apparent reason :eek: :no: :wacko: :huh:

Has ANYONE experienced the same issue? If so what was your fix/ resolution?

Calling Penn State tomorrow morning :taz:

THIS SUCKS!!!!!!
Logged

Offline Parker

  • Global Mentor & Moderator
  • Custom Call Maker
  • *
  • Posts: 6435
  • Location: Whitetail Country
  • VECtor Custom Calls
    • VECtor Custom Calls
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #1 on: March 10, 2010, 12:23:43 AM »
The easiest thing to have go out on a lathe is the power switch.  I was lucky enough this last time to have mine go out in the 'on' position. 

Have you checked the switch to make sure you are still getting current through it?

No matter what type of lathe you have, as much as we turn them on and off, they are going to give.

I SURE hope this is your problem, because it is a cheap fix at your local hardware store.

Parker
Logged
Art is not in the eye of the beholder. It's in the soul of the artist.
Pass on the tradition. A candle loses nothing by lighting another candle.

VECtor Custom Calls
Deer Grunt Calls Turkey Calls and Other Custom Game Calls

Offline Braz

  • Administrator
  • Custom Call Maker
  • *
  • Posts: 6649
  • Age: 68
  • Location: Yuba City, Natzifornia
    • Calls by Braz
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #2 on: March 10, 2010, 12:42:05 AM »
Yep, I agree, I believe that is the first thing I would check.
Logged
Braz
"Suppose you were an idiot. And suppose you were a member of Congress.. But I repeat myself."--Mark Twain

Offline greenwell1978

  • Custom Call Maker
  • *****
  • Posts: 120
  • Age: 33
  • Location: Morganfield, KY
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #3 on: March 10, 2010, 05:31:20 AM »
thats what happen to mine and it was the switch
Logged

Offline MUTT

  • Duck & Goose Call Mentor
  • Custom Call Maker
  • *****
  • Posts: 1405
  • Age: 48
  • Location: Currituck, NC
  • MUTT Game Calls
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #4 on: March 10, 2010, 05:45:27 AM »
Interesting.  I was using my Delta just yesterday and it quit as well in th "ON" position.  Have to go out and get a new switch this morning.

Mutt
Logged
For it is in the Woods, Fields, & Marshes that Retrievers make thier own legends... and become our heroes!



Curriduck@cox.net

Offline Fyrewil

  • Custom Call Maker
  • *****
  • Posts: 13
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #5 on: March 10, 2010, 08:41:16 AM »
Update: Just got off the phone with PSI, they are thinking the same (VS control box fuse and or reostat). fuse no issue quick fix... Reostat would have to send back to PSI to be repaired or replaced.
I will have to remove the VS control box tomorrow to check the fuse. heading ot to work 24 hr shift...
I will update when I find out.
Thank you for the replies!
Willie
Logged

Offline TheJester357

  • Global Mentor & Moderator
  • Custom Call Maker
  • *
  • Posts: 1361
  • Age: 40
  • Location: Dallas, OR
  • Eames Custom Calls
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #6 on: March 10, 2010, 09:27:27 AM »
The other thing that goes wrong with those things is the transistor that controls the current of the Motor. I have a few dozen if that is the problem.

 Bob
Logged
Life, Liberty, and the pursuit of anything with web feet.

 Charter member of the Cooper Hollow Mafia

Offline Fyrewil

  • Custom Call Maker
  • *****
  • Posts: 13
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #7 on: March 11, 2010, 02:22:36 PM »
Update: Double checked lathe today before checking fuse, plugged in will not turn on, push reset button on VS control. nada no power will not turn on.

turn lathe on side to remove vs control box to check fuse per PSI, fuse intact still good..... set lathe up right to clear cord to get ready to ship out. (Hum let me double check) plugged in cord and turn switch on and WE HAVE POWER!!!

Wait a minute.... I didnt do anything to it.... So I unplugged the cord, turned the lathe back over and started to check connections, all connections tight including the fuse, so I called PSI and advised same and inquired what they would like for me to do...

PSI: run and see if it happens again... it may last for 2 minutes or it may runn for the next 5 years without an issue.

So we are turning wood today!!! at least until it stops!

Willie
Logged

Offline Parker

  • Global Mentor & Moderator
  • Custom Call Maker
  • *
  • Posts: 6435
  • Location: Whitetail Country
  • VECtor Custom Calls
    • VECtor Custom Calls
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #8 on: March 11, 2010, 03:08:44 PM »
Sounds to me like you had crud in your on/off switch, and it shook loose.  But I suppose there are a hundred different things it could be. 

Parker
Logged
Art is not in the eye of the beholder. It's in the soul of the artist.
Pass on the tradition. A candle loses nothing by lighting another candle.

VECtor Custom Calls
Deer Grunt Calls Turkey Calls and Other Custom Game Calls

Offline jcz

  • Custom Call Maker
  • *****
  • Posts: 2492
  • Age: 34
  • Location: Pinetops ,NC
  • You want some??
    • Trophygamecalls
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #9 on: March 11, 2010, 07:52:44 PM »
Hope it was crud!! Good luck. I know Id be sick ( or should I say I will be sick) when mine dies.
Logged
August Call Makers Throwdown Winner
http://www.trophygamecalls.embarqspace.com/

Offline cterese12

  • Custom Call Maker
  • *****
  • Posts: 107
  • Age: 32
  • Location: Abita Springs, LA
Re: Turncrafter Pro VS DIED!!!!!!
« Reply #10 on: March 12, 2010, 08:09:31 PM »
i had to replace my switch a couple months ago as well.  its not a psi, but as stated it will fail at some point.  easy fix though.  it is a sad day when the lathe bunks!
Logged
Bringin'em down one flock at a time


Pages: [1]   Go Up
« previous next »